STATIC METER - LOCATOR AND MEASURER: #EOS-100
DÉGAGÉ CORP. Static meter model EOS-100 is the only hand held meter offering five volt accuracy at 100 volts full scale. This battery operated meter can be used to conduct static audits, locate the source of static and measure the degree of static within an accuracy level of 5% full scale. The unit weighs nine ounces, has a .5 second response time and measures 5-1/2"x2-1/2"x1-3/4" and comes in its own padded vinyl case. This meter is an industry standard and no other meter offers the sensitivity of the EOS-100, with 100 volt scale and 2 volt resolution.

IONIZER TESTER: #11050
DÉGAGÉ CORP. Ionizer tester model #11050 is a hand held ionizer tester designed to insure compliance with ESD program requirements. This meter will enable you to audit your ionizers daily, at the workbench, in less than ten seconds. This is a reliable evaluation of your ionizers performance. Our model #11050 is a hand held charge plate monitor operating on a nine volt battery that will tell you quickly whether your ionizer is working and whether your ION stream is balanced and neutralizing all static build up.

RESISTIVITY METER #RT-1000
DÉGAGÉ CORP. Resistivity meter model #RT-1000 megohmmeter is designed to test all conductive, antistatic, and static dissipative surfaces for electrical resistivity/resistance according to ESD, CECC, ANSI, ASTM and UL test procedures. It is easy to use and is of high quality and dependability. The meter also measures relative humidity and temperature both of which affect electrical properties, aiding in the identification of costly rejects. FEATURES: Measures resistivity, temp., f or c and humidity. - 10 volts & 100 volts - test range of 10^3rd to 10^12th OHMS/SQ. - LCD scale - auto shut off - parallel and 5# probes. - Concentric ring probe - 9 volt dc or ac adaptor - ISO 9000 conformance - Meets ANSI/ESD standard 11.11.

RESISTIVITY METER 2-#SRM-RTG
DÉGAGÉ CORP. Model SRM-RTG resistivity meter is simple to use, highly repeatable and is a measuring device for determining the surface resistivity as well as the resistance to ground of materials. Settings measure from 10^4th OHMS/SQ. To 10^12th OHMS/SQ. DÉGAGÉ'S SRM-RTG meter is normally used to test the resistivity of static control bags, mats, conductive floors, coatings, packaging materials, boxes, sprays and wipes. The meter indicates the level of resistance through 10 LCD lights with each one indicating a level of resistance. This meter can also be used to measure resistance to ground in ohms, of materials used for static dissipation such as floor tiles and mats.

WRIST STRAP, HEEL STRAP TESTER # GST-400
DÉGAGÉ model GST-400 is designed to permit a fast, simple, safe and convenient means to test the resistance of work surfaces of table tops, mats, etc. To ground through a wrist strap, but may also be used to test heel straps by using an optional connected stand-on conductive mat. The work surface may be tested by simply pressing the bottom on the far end corner of the lid of the GST- 400. To test an operator wearing a wrist strap, the lid itself is pressed to insure proper resistance to ground. Three, go no-go lights are incorporated to indicate o.k., hazard or high resistance and a warning buzzer is built in. Resistance of up to 10^ 8th OHMS/SQ. to ground can be tested and monitored. This meter is an industry standard and featured in most training videos.

WRIST STRAP MONITOR-DUAL OPERATOR #CM-500
DÉGAGÉ Model CM-500 is a dual operator constant monitor, designed to enable constant resistant monitoring to ground of two operators, with specially designed double contact stainless steel flex band wrist straps and coil cords. The CM-500 tests for a resistance to ground greater than 1.3 megohms, at its lower limit, and less than 39 megohms at its upper limit. The unit is AC powered. The CNI-500 is easily mounted between two work stations so that two operators can be monitored.

WRIST STRAPS-DUAL CORD-FOR USE WITH #CM-500
Adjustable cloth wrist strap with dual cords.
Metal flex wrist strap with dual ground cords.

IONIZER BENCH MOUNTED - NON NUCLEAR
Model VSE-3000 bench mounted ionizing unit will rid your ESD protected work area of static charges with a stream of ionized air from this volume static eliminator. This instrument does what wrist straps, heel straps and ground straps cannot do. It removes static charges from insulators and all non conductive objects. The VSE-3000 quickly neutralizes such items as paper, clothing, and all insulators that find their way to the work bench and static sensitive components. The VSE- 3000 reduces charges faster than any other product because it generates more ION current. Our VSE-3000 is effective over a larger surface area because it provides an air velocity of 550ft./min. at 2' when switched to high speed, with an angle of coverage of 60 degrees. Dimensions are 12"x6.25"x10” and the emitter assembly has a 50,000 hour life expectancy.

CONDUCTIVE BRUSHES AND STATIC DISSIPATIVE GARLAND
DÉGAGÉ conductive brushes and garland are inexpensive ways to eliminate static charges on such items as printing presses, paper and rewind rolls, polyethylene winding machines and other industrial applications. Both brushes and garland are custom sized and designed specifically for your application and will normally require some installation and custom mounting brackets. Inquire for price and availability

CONDUCTIVE COPPER TINSEL
DÉGAGÉ # 36125 Steltin, conductive copper tinsel, is wound on a wire core and used to eliminate static on printing presses, roll paper, cloth and film winders and other areas, where an inexpensive but effective solution adaptable to wide width machinery is required. Mounting brackets will have to be fabricated for each operation and the copper tinsel should be strung across the machine web and grounded. Each master carton of copper tinsel contains 24 rolls, each roll 1-1/2"x36' and the master case contains a total length of 864'.