DC-1300-CT CleanTuff Tubing Class 100 - 2Mil, 3Mil, 4Mil, 6Mil, 8Mil, 10Mil

"CleanTuff" FILM PHYSICAL PROPERTIES
PHYSICAL PROPERTIES	Material - "CleanTuff" LPDE Available As - Lay-flat tubing, Sheeting & Bags. Clarity - Transparent Thickness - .002Mil - .008Mil;
Film Properties	ASTM Method	Units	Typical Value
Tensile Strength (Break)	D-882	PSI
MD	•	•	4350
TD	•	•	4270
Elongation (Break)	0-882	%	•
MD	•	•	410
TD	•	•	675
Dart Drop Impact	D1709	Grams	263

Note: All values given are based on a 1.25mil thick film
Typical values represent laboratory values and are intended as guides only, not specifications.

CleanTuff Ionic Contamination TESTING

  In the chart below are listed test results showing the degree of ionic contamination for DegageCorp’s product line of class 100 or class 5 cleanroom bags, films and tubing. The anions and cations are shown as the lowest levels achievable. The ammonium, as shown in the chart, is the result of polyethylene amide groups which contain low levels of NH3 groups. It is also partly attributable to our deionizing process which releases minute particles of ammonium into the atmosphere.

  The test results, done by an outside laboratory, do not reflect a cleanliness level (ie: class 100 to class 5) or a particulation size or count for a cleanliness classification, but they are indicative of the chemical makeup of any flossing, leeching, or out-gassing that could occur in the packaging of micro-contamination sensitive parts (out-gassing organics ATD• GC/MS). Our low out-gassing and low particulation levels have led many of our 'customers to claim that our bags, films and tubing are "The most consistently clean in the industry."

MATERIAL SAFETY DATA SHEET

DegageCorp . 002 MIL CLEAR NYLON BAGS, TUBING AND FILM. 

Composition/Information on Ingredients

Trace impurities and additional material names not listed above may also appear in the Regulatory Information section towards the end of the MSDS. These materials may be listed for local "Right to Know" compliance and for other reasons.

HAZARDS IDENTIFICATION:
EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:
SKIN: Not considered hazardous.
EYES: Not considered hazardous. May cause mechanical irritation if film comes into contact with the eye.
INHALATION: Not a route of exposure under normal usage. Elevated processing temperatures may release irritating vapors.
INGESTION: NOT a route of exposure. Not considered hazardous.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.
ADDITIONAL RECOMMENDATIONS: None

EXPOSURE GUIDELINES:

** = Workplace Environmental Exposure Level (AlHA).
*** = Biological Exposure Index (ACGIB).

OTHER EXPOSURE LI~UTS FOR POTENTIAL DECOMPOSITION PRODUCTS: None

PHYSICAL AND CHEMICAL PROPERTIES

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

IMMEDIATE (ACUTE) EFFECTS: Not determined.
DELAYED (SUBCHRONIC &CHRONIC) EFFECTS: None known
ECOLIGICAL INFORMATION: Material is considered inert and not expected to be biodegradable or toxic.
DISPOSAL CONSIDERATIONS: Not Applicable
RCRA: Is the unused product a RCRA hazardous waste if discarded?  No
If yes, the RCRA ID number is:

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable


REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE IU/CERCLA: "Reportable Quantities"(RQs) and/or "Threshold Planning Quantities" (TPQs) exist for the following ingredients:

Spills resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (1- 800-424-8802) and. to your local emergency planning committee.

SECTION 311 HAZARD CLASS: None

SARA 313 TOXIC CHEMICALS: The following ingredients are SARA 313 "Toxic Chemicals". CAS #'s and weight percents are found under composition/information on ingredients.

Additional Regulatory Information: The base monomers listed on the EINECS Inventory
WHM'S CLASSIFICATION (CANADA): Not a controlled substance. (Considered to be a manufactured article)