DC-1450 Low Density Polyethylene Anti-Static Zipper Bags - 2Mil, 4Mil

DC-1450 Anti-Static Low Density Polyethylene Zipper Bags


What Is ESD Protection?

 DegageCorps. Pink or clear low density polyethylene anti-static zipper bags are available in 2mil and 4mil in a side seal configuration and in widths of 1.5" to 60" and any length that is required. DegageCorps. anti-static zipper bags are manufactured using a permanent anti-static resin and an anti-static extruded zipper that totally eliminates all leaching and outgassing from the anti-static additive while enhancing the finished bag with an air tight seal. DegageCorp's. DC-1450 is a non-cleanroom product and is made per order with an average delivery being 3 weeks.

 BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Physical Properties
Material  Polyethylene
Available As: Lay-Flat Tubing, Sheeting & Bags
Clarity: Transparent
Thickness: .002Mil - .008Mil


Film Properties ASTM Method Units Typical Value
Density   D-1505 g/cm3 0.920
Tensile Strength D-882 PSI
MD 2900
TD 2300
Elongation (Break) D-882 %
MD
TD
Dart Drop Impact   D-1709 Grams 80-100

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

INGREDIENT NAME CAS# Weight %
Low Density Polyethylene (Nonhazardous) 9002-88-4 Proprietary

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:
Occupational Exposure: Nuisance dust TLV: 10mg/m(ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respritory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear Thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

PHYSICAL STATE Solid
ODOR None
SPECIFIC GRAVITY (Water = 1.0) 0.90 - 0.92
SOLUBILITY IN WATER <"Weight %) Negligible
pH Not applicable
BOILING POINT Not applicable
MELTING POINT 100°C-120°C (212°F-248°F)
VAPOR PRESSURE Not applicable
VAPOR DENSITY (Air = 1.0) Not determined
EVAPORATION RATE Not applicable
COMPARED TO Not applicable
% VOLATILES Negligible
FLASH POINT > 343°C (650°F)

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence  of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use and/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Governors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979 (Monday-Friday, 9:00am-5:00pm - central standard time)

 It is your responsibility to determine that our product is safe, lawful, and technically suitable for your intended uses. This material safety data sheet cannot cover all possible situations which the user may experience during processing. Each aspect of the user’s operation should be examined to determine if, or where, additional precautions may be necessary. All health and safety information contained in this material safety data sheet should be provided to employees and/or customers. DegageCorp must rely on the user to use this information to develop appropriate work practice guidelines and employee instructional programs specific to the user’s operation.
 
 As the conditions and methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of these products. The information contained herein is believed to be true and accurate, but all statements or suggestions are made without warranty, expressed, or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof. Compliance with all applicable international, federal, state, and local laws and regulations regarding the use, storage, sale, transport or disposal of this material is the responsibility of the user.
 
 DegageCorp. does not endorse or claim suitability of its product for any particular use. DegageCorp. MAKES NO WARRANTY OF MERCHANTABILITY AS TO ITS LDPE RESINS. DegageCorp. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, CONCERNING THE SUITABILITY OR FITNESS OF ANY DegageCorp. PRODUCT FOR ANY PARTICULAR USE. DegageCorp's liability and your exclusive remedy for any claim arising out of the sales of its products are expressly limited at DegageCorp's  option to replacement of non-performing goods or payment not to exceed the purchase price plus transportation charges thereon in respect to any material which damage is proven and claimed.
 
 The information in this MSDS is valid for cited regulations published as of the date this document was prepared, as shown on page 1. Updates may be prepared as the regulations are amended or pending revised information about the resin. It is the customer’s responsibility to seek updated regulatory information on any specific resin.

Anti-Static LDPE Bags - Anti-Static Zipper Bags - Anti-Static Pink - Anti-Static Clear Zipper Bags