Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp . 002 - .008 LDPE   Composition/Information on Ingredients

Trace impurities and additional material names not listed above may also appear in the Regulatory Information section towards the end of the MSDS. These materials may be listed for local "Right to Know" compliance and for other reasons.

HAZARDS IDENTIFICATION:
EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:
SKIN: Not considered hazardous.
EYES: Not considered hazardous. May cause mechanical irritation if film comes into contact with the eye.
INHALATION: Not a route of exposure under normal usage. Elevated processing temperatures may release irritating vapors.
INGESTION: NOT a route of exposure. Not considered hazardous.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.
ADDITIONAL RECOMMENDATIONS: None

EXPOSURE GUIDELINES: 

** = Workplace Environmental Exposure Level (AlHA).
*** = Biological Exposure Index (ACGIB).

OTHER EXPOSURE LI~UTS FOR POTENTIAL DECOMPOSITION PRODUCTS: None

PHYSICAL AND CHEMICAL PROPERTIES

STABILITY AND REACTIVITY: 

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

IMMEDIATE (ACUTE) EFFECTS: Not determined.
DELAYED (SUBCHRONIC &CHRONIC) EFFECTS: None known
ECOLIGICAL INFORMATION: Material is considered inert and not expected to be biodegradable or toxic.
DISPOSAL CONSIDERATIONS: Not Applicable
RCRA:
Is the unused product a RCRA hazardous waste if discarded?  No
If yes, the RCRA ID number is:

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.

The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE IU/CERCLA: "Reportable Quantities"(RQs) and/or "Threshold Planning Quantities" (TPQs) exist for the following ingredients:

Spills resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (1- 800-424-8802) and. to your local emergency planning committee.

SECTION 311 HAZARD CLASS: None

SARA 313 TOXIC CHEMICALS: The following ingredients are SARA 313 "Toxic Chemicals". CAS #'s and weight percents are found under composition/information on ingredients.

STATE RIGHT TO KNOW: In addition to the ingredients found in section composition/information on ingredients. The following are listed for state Right-to-know purposes:

"CleanTuff" FILM PHYSICAL PROPERTIES
PHYSICAL PROPERTIES	Material - "CleanTuff" LPDE Available As - Lay-flat tubing, Sheeting & Bags. Clarity - Transparent Thickness - .002Mil - .008Mil;
Film Properties	ASTM Method	Units	Typical Value
Tensile Strength (Break)	D-882	PSI
MD	•	•	4350
TD	•	•	4270
Elongation (Break)	0-882	%	•
MD	•	•	410
TD	•	•	675
Dart Drop Impact	D1709	Grams	263

Note: All values given are based on a 1.25mil thick film
Typical values represent laboratory values and are intended as guides only, not specifications.

CleanTuff Ionic Contamination TESTING

  In the chart below are listed test results showing the degree of ionic contamination for DegageCorp’s product line of class 100 or class 5 cleanroom bags, films and tubing. The anions and cations are shown as the lowest levels achievable. The ammonium, as shown in the chart, is the result of polyethylene amide groups which contain low levels of NH3 groups. It is also partly attributable to our deionizing process which releases minute particles of ammonium into the atmosphere.

  The test results, done by an outside laboratory, do not reflect a cleanliness level (ie: class 100 to class 5) or a particulation size or count for a cleanliness classification, but they are indicative of the chemical makeup of any flossing, leeching, or out-gassing that could occur in the packaging of micro-contamination sensitive parts (out-gassing organics ATD• GC/MS). Our low out-gassing and low particulation levels have led many of our 'customers to claim that our bags, films and tubing are "The most consistently clean in the industry."

MATERIAL SAFETY DATA SHEET

DegageCorp . 002 MIL CLEAR NYLON BAGS, TUBING AND FILM. 

Composition/Information on Ingredients

BALAZS ANALYTICAL TESTING SERVICES                                                   "CleanTuff Test Results"
Analyte	Reporting Limit (ug/Cm2)	Sample 1 CleanTuff	Sample 2 A/S Poly CleanTuff
Bromide	0.001	•	•
Chloride	0.002	•	•
Fluoride	0.002	•	•
Nitrate	0.002	•	•
Nitric	0.002	•	•
Phosphate	0.002	•	•
Sulfate	0.001	•	•
Ammonium	0.0001	0.001	0.032
Potassium	0.007	•	•
Sodium	0.007	•	•

INGREDIENT NAME	CAS#	Weight %
Polycaprolactam (Non hazardous)	25038-54-4	Proprietary

Trace impurities and additional material names not listed above may also appear in the Regulatory Information section towards the end of the MSDS. These materials may be listed for local "Right to Know" compliance and for other reasons.

HAZARDS IDENTIFICATION:
EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:
SKIN: Not considered hazardous.
EYES: Not considered hazardous. May cause mechanical irritation if film comes into contact with the eye.
INHALATION: Not a route of exposure under normal usage. Elevated processing temperatures may release irritating vapors.
INGESTION: NOT a route of exposure. Not considered hazardous.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.
ADDITIONAL RECOMMENDATIONS: None

EXPOSURE GUIDELINES:

INGREDIENT NAME	ACGIH TLV	OSHA PEL
		TW A = 20mg/m3   STEL = 40mg/m3

** = Workplace Environmental Exposure Level (AlHA).
*** = Biological Exposure Index (ACGIB).

OTHER EXPOSURE LI~UTS FOR POTENTIAL DECOMPOSITION PRODUCTS: None

PHYSICAL AND CHEMICAL PROPERTIES

PHYSICAL STATE	Solid
ODOR	None
SPECIFIC GRAVITY (Water = 1.0)	1.05-1.25
SOLUBILITY IN WATER <"Weight %)	Negligible
pH	Not applicable
BOILING POINT	Not applicable
MELTING POINT	220-223°C (428-433°F)
VAPOR PRESSURE	Negligible at room temperature
VAPOR DENSITY (Air = 1.0)	Not determined
EVAPORATION RATE	Not applicable
COMPARED TO	Not applicable
% VOLATILES	Negligible
FLASH POINT	> 400°C

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

IMMEDIATE (ACUTE) EFFECTS: Not determined.
DELAYED (SUBCHRONIC &CHRONIC) EFFECTS: None known
ECOLIGICAL INFORMATION: Material is considered inert and not expected to be biodegradable or toxic.
DISPOSAL CONSIDERATIONS: Not Applicable
RCRA: Is the unused product a RCRA hazardous waste if discarded?  No
If yes, the RCRA ID number is:

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable


REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE IU/CERCLA: "Reportable Quantities"(RQs) and/or "Threshold Planning Quantities" (TPQs) exist for the following ingredients:

INGREDIENT	SARA/CERCLA RQ (lb)	SARA EHS TPO (Ib)
No ingredients listed in this section

Spills resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (1- 800-424-8802) and. to your local emergency planning committee.

SECTION 311 HAZARD CLASS: None

SARA 313 TOXIC CHEMICALS: The following ingredients are SARA 313 "Toxic Chemicals". CAS #'s and weight percents are found under composition/information on ingredients.

INGREDIENT	COMMENT
No ingredients listed in this section

STATE RIGHT TO KNOW: In addition to the ingredients found in section composition/information on ingredients. The following are listed for state Right-to-know purposes:

INGREDIENT	WT.%	COMMENT
No ingredients listed in this section

Additional Regulatory Information: The base monomers listed on the EINECS Inventory
WHM'S CLASSIFICATION (CANADA): Not a controlled substance. (Considered to be a manufactured article)

For other information, contact Degage Corp. (972) 524 - 2979 (Monday-Friday, 9:00am-5:00pm - central standard time) It is your responsibility to determine that our product is safe, lawful, and technically suitable for your intended uses. This material safety data sheet cannot cover all possible situations which the user may experience during processing. Each aspect of the user’s operation should be examined to determine if, or where, additional precautions may be necessary. All health and safety information contained in this material safety data sheet should be provided to employees and/or customers. Degage Corp must rely on the user to use this information to develop appropriate work practice guidelines and employee instructional programs specific to the user’s operation. As the conditions and methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of these products. Information contained herein is believed to be true and accurate, but all statements or suggestions are made without warranty, expressed, or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof. Compliance with all applicable international, federal, state, and local laws and regulations regarding the use, storage, sale, transport or disposal of this material is the responsibility of the user. Degage Corp. does not endorse or claim suitability of its product for any particular use. Degage Corp. MAKES NO WARRANTY OF MERCHANTABILITY AS TO ITS LDPE RESINS. Degage Corp. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, CONCERNING THE SUITABILITY OR FITNESS OF ANY Degage Corp. PRODUCT FOR ANY PARTICULAR USE. Degage Corp's liability and your exclusive remedy for any claim arising out of the sales of its products are expressly limited at Degage Corp's option to replacement of non-performing goods or payment not to exceed the purchase price plus transportation charges thereon in respect to any material which damage is proven and claimed. The information in this MSDS is valid for cited regulations published as of the date this document was prepared, as shown on page 1. Updates may be prepared as the regulations are amended or pending revised information about the resin. It is the customer’s responsibility to seek updated regulatory information on any specific resin.

Cleanroom Tubing - Cleanroom Tube - Cleanroom Packaging - Cleanroom Bags - Cleanroom Pouches - Cleanroom Tubing - Cleanroom Sheets - Cleanrrom Sheeting - CleanTuff Poly

 DegageCorps. low density, polyethylene, cleanroom, class 100, ISO Class 5 vapor barrier tubing is made from a mono structure film extruded in a FED. Cert 209E cleanroom that exhibits the characteristics of low vapor transmission while meeting the strict cleanliness specifications of JPG 5322-1 Level 100. Our mono film is extruded from a blend of low density resins that contain no release agents, slip agents, or manufacturing aides. See CleanTuff for additional specifications and test results. 

What Is JPG 5322.1G?    BPA Free Guarantee      BSE TSE Animal Component Free Guarantee      Latex Free Guarantee

 DegageCorps. Class 100 ldpe cleanroom, narrow width tubing is extruded from virgin resin, special order, polyethylene resin without the addition of any manufacturing aides, slip agents or release agents. Our narrow width clean tube is available in very narrow widths and thin thicknesses and extruded and fabricated and wound on PVC cores inside a Fed.209e cleanroom. Because our films are both extruded and fabricated inside of a class 5 cleanroom our films are just as clean on the outside as they are on the inside. Only, DegageCorp. can offer this unique advantage to mitigate contamination. Call today for pricing on your custom clean room tube lengths and widths. 

    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp . 002 - .008 LDPE         Composition/Information on Ingredients

Trace impurities and additional material names not listed above may also appear in the Regulatory Information section towards the end of the MSDS. These materials may be listed for local "Right to Know" compliance and for other reasons.HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:

SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.

EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.

RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear Thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence  of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.

The information offered here is for the products shipped. Use and/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification ( Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

What Is JPG 5322.1G?    What Is MIL-PRF-81705D?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

What Is JPG 5322.1G?    What Is MIL-PRF-81705D?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Cleanroom Tubing - Cleanroom Tube - Cleanroom Packaging - Cleanroom Bags - Cleanroom Pouches - Cleanroom Tubing - Cleanroom Sheets - Cleanroom Sheeting - CleanTuff Poly - 

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

Respritory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Governors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

  DegageCorp. Class 100 (ISO Class 5) clean room film ("Metal-In") static shielding bags will also meet the military specification of MIL-PRF-81705D, type 3 as well as the cleanliness specification of NASA JPG 5322-1 Level 100 and ISO 14644-1 Class 5. DegageCorps. metalized static shielding bags are a 3mil composite consisting of an outer layer of static dissipative coating applied to a layer of polyester that is vacuum deposited with a conductive aluminum metal coating and laminated to an inner layer of permanent static dissipative 10^8th low density polyethylene. The DegageCorp. Transparent static shielding bag provides complete shielding from electrostatic discharge, RFI frequencies and EMI impulses. DegageCorps. static shielding bags instantly dissipate static charges. Loaded circuit boards can be safely handled and stored, shipped and are readily identified without removal when placed in our transparent static shielding bags. Your products are static secure and totally enclosed in a Faraday Cage environment. Electrostatic voltages applied to the outside of the bag cannot affect components within the bag. This is not the case with  Anti-Static bags which slowly dissipate static charges. Slow dissipation generally results in increased voltages inside anti-static polyethylene bags, potentially causing component degradation. The DegageCorp. Transparent static shielding is the best protection available for static sensitive components that are being brought into an ISO Class 5 cleanroom.

Cleanroom Static Shielding Bags - Cleanroom Static Shielding Zip Lock Bags - Cleanroom Static Shielding Gusseted Bags - Cleanroom Static Shielding Wafer Boat Bags - Cleanroom Static Shielding Pouches

Class 100  Static Shielding Bags - Class 100 Static Shielding Zip Lock Bags - Class 100 Static Shielding Gusseted Bags - Class 100 Static Shielding Wafer Boat Bags - Class 100 Static Shielding Pouches - Cleanroom Gusseted - Class 100 Gusseted - Cleanroom Packaging - Class 100 Packaging 

What Is JPG 5322.1G?    What Is MIL-PRF-81705D?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

 DegageCorps. Pink or clear low density polyethylene anti static ziplock bags are available in 2mil and 4mil in a side seal configuration and in widths of 1.5" to 60" and any length that is required. DegageCorps. anti-static zipper bags are manufactured using a permanent anti-static resin and an anti-static extruded zipper that totally eliminates all leaching and outgassing from the anti-static additive while enhancing the finished bag with an air tight seal. DegageCorp's. DC-1450 is a non-cleanroom product and is made per order with an average delivery being 3 weeks.

 BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:
Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respritory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear Thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence  of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use and/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Governors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979 (Monday-Friday, 9:00am-5:00pm - central standard time)

Anti-Static LDPE Bags - Anti-Static Zipper Bags - Anti-Static Pink - Anti-Static Clear Zipper Bags 

 DegageCorp. notched tear-strip bags are manufactured from a blend of resins that impart a molecular structure to the film or bag that when notched or cut tear in a straight line, the length of the bag, for ease of product removal. DegageCorps. tear strip bags are available in 3mil clear and can either be hot stamped or printed. Tear strip bags are heavily used in the packaging of medical supplies and medical instruments. DegageCorps. tear strip bags are custom made to the customers specifications and require a 3 week manufacturing time. 

    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

 For other information, contact Degage Corp. (972) 524 - 2979 (Monday-Friday, 9:00am-5:00pm - Central Standard Time) It is your responsibility to determine that our product is safe, lawful, and technically suitable for your intended uses. This material safety data sheet cannot cover all possible situations which the user may experience during processing. Each aspect of the user’s operation should be examined to determine if, or where, additional precautions may be necessary. All health and safety information contained in this material safety data sheet should be provided to employees and/or customers. Degage Corp must rely on the user to use this information to develop appropriate work practice guidelines and employee instructional programs specific to the user’s operation. As the conditions and methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of these products. Information contained herein is believed to be true and accurate, but all statements or suggestions are made without warranty, expressed, or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof. Compliance with all applicable international, federal, state, and local laws and regulations regarding the use, storage, sale, transport or disposal of this material is the responsibility of the user. Degage Corp. does not endorse or claim suitability of its product for any particular use. Degage Corp. MAKES NO WARRANTY OF MERCHANTABILITY AS TO ITS LDPE RESINS. Degage Corp. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, CONCERNING THE SUITABILITY OR FITNESS OF ANY Degage Corp. PRODUCT FOR ANY PARTICULAR USE. Degage Corp's liability and your exclusive remedy for any claim arising out of the sales of its products are expressly limited at Degage Corp's option to replacement of non-performing goods or payment not to exceed the purchase price plus transportation charges thereon in respect to any material which damage is proven and claimed. The information in this MSDS is valid for cited regulations published as of the date this document was prepared, as shown on page 1. Updates may be prepared as the regulations are amended or pending revised information about the resin. It is the customer’s responsibility to seek updated regulatory information on any specific resin.

 DegageCorps. low density Cleanroom ldpe packaging poly bags bottom seal, certified class100 cleanroom, hot stamped, are extruded from virgin resin, without the addition of anti-block or slip agents, and are fabricated "in line" in a federal 209e cleanroom.  All printing or hot stamping is done as a separate operation, in a controlled environment. All printing is outside coated, and will meet all specifications of JPG 5322-1 level 100 or ISO 14644-1 class 5. Call today for a quote on this clean ldpe packaging available in custom sizes.

What Is JPG 5322.1G?    What Is JPG 14644?     BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES: 

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use and/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification ( Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information : 

For other information, contact Degage Corp. (972) 524 - 2979

What Is JPG 5322.1G?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

  DegageCorp. Class 100 - ISO Class 5 - "Metal-In" static shielding zip lock bags, are identical to DC-7000-C with the addition of a Zip Lock, reclosable feature and they will meet the spec MIL-PRF-81705D Type III as well as the particulation requirements of NASA JPG 5322-1 Level 100 and ISO 14644-1 Class 100. All bags are fabricated inside of a Fed Cert 209e cleanroom using a special zip lock system that assures a air tight seal for use in a Class 5 Cleanroom. All sizes are available in mil thicknesses of 2mil and 4mil, average delivery time is 3-4 weeks. 

Cleanroom Zipper bags - Cleanroom Static Shielding - Cleanroom gusseted - Cleanroom Zip Lock - Class 100 Zipper bags - Class 100 Gusseted - Cleanroom Zipper Packaging - Class 100 Zipper Packaging 

1000 Labels per roll, labels have non permanent adheasive backing. Each Roll is $20.00

Minimum Company Order: $125.00 USD
Terms: Master Card or Visa Only, with a 3.5% service fee added.

Shipment is within 48hrs from time of payment.

Shipping Handling and freight fee is $10.00 for prepaid freight anywhere in the USA.

  DegageCorp. Class 100 (ISO Class 5) clean room Nylon Poly laminated bags and tubing are a bi-extrusion of 2 mils of Dupont nylon laminated to 3 mils of low density virgin resin that will meet the stringent cleanliness requirements of Nasa JPG 5322-1 level 100. While giving superior puncture resistance and outstanding moisture vapor barrier characteristics. DC-2070-C is available in bag sizes up to 48" wide and lengths up to 60". DegageCorps. nylon and nylon laminated bags are fabricated within the confines of a vertically integrated federally certified 209E clean room and are designed for the critical packaging of electronics, medical instruments, implants, orthopedic devices, spinal products and neurosurgical devices as well as ceramics, thin films and fiber optics. Because of DegageCorps. vertical integration we have achieved shipping times of an estimated two weeks, from an industry standard of twelve weeks, giving our customers greater inventory turnaround and increased cost effectiveness. 

What Is JPG 5322.1G?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

  DegageCorp. anti-static low density polyethylene (MIL PRF-81705 D) handmade pink, clear or black conductive square bottom covers are made from low density polyethylene with a permanent anti-static additive that eliminates all leaching, flossing or migration to the surface of any static residue. Square bottom covers are custom ordered only and are assembled in our "HandMade" department to our customers specifications. Most square bottom covers are designed to protect large electronic switching terminals and transformers from the effects of static caused failures and each cover is specifically designed to the customer's specifications and requirements. Handmade static covers are available in any size and configuration from 3 mil to 6 mil and are assembled on our large Vertrod sealer, one of the very few in our industry. DegageCorp. has the capability of manufacturing covers up to 8' in width and 8' in height. Square Bottom Covers are also available in Class 100 Clean Room Poly configurations

 BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute subchronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Governors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification ( Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

Pallet Covers - Square Bottom Covers - Pallet Sheets - Anti-Static LDPE - 

  DegageCorps. "Soft Foot" static dissapative 10^8th Ohms./Sq., Electronics, anti fatigue mats are 3/8" thick and master roll sizes are 3'X60' and 5'X60'. Soft Foot mats have beveled sides. These are very high quality mats to be used at stand up electronic work stations and are not made for chairs to roll on. This mat will cut a workers foot fatigue by 70%. Available finishes are 1. Pebble embossed and 2. Wide rib and available colors are brown and grey. All mats are cut to size and a standard grounding snap is installed.

Degage Corp. Conductive Copper Tinsel  is an inexpensive way to eliminate static charges on such items as paper presses, printing presses,paper and rewind rolls and all wide web industrial applications.

 Conductive copper tinsel is generally used in the printing and weaving industries to eliminate the flow of static that is generated by wide web machinery.  Copper tinsel strung across the web of a machine and spaced 1/32^nd. Of an inch above the web will direct all accumulated static charges to ground, and eliminate most, if not all, tribo- charging.

 Degage Conductive Copper Tinsel is packaged 24 coils per master carton.  Each coil is 1 ½”x12 yd. in length for a total master carton length of 864’.  

 Price:  $200.00 per master carton. Minimum sales unit is 1 master carton. Terms:  Net. Master Card and Visa only with an additional 3.5% service charge added.  Shipping and Handling is $12.00 U.S. per master carton which DegageCorp.will ship prepaid to any U.S. location.  Delivery is immediate from warehouse stock.

 DegageCorp High Density Polyethylene clean room bags and tubing are extruded and fabricated “in line” in a Fed. Cert 209e cleanroom. All high density bags and tubing are extruded from custom ordered cleanroom, high density resin without the addition of any manufacturing aides, release agents or slip agents and the tubing is fabricated "in line" into bottom seal bags and open tube that will exceed the specifications of JPG 5322-1 Class100 as well as ISO 14644-1 CLASS 5.

What Is JPG 5322.1G?    What Is JPG 14644?     BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Available in the following configurations: Cleanroom Poly Bags - Cleanroom Zip Lock Poly Bags - Cleanroom Poly Tubing - Cleanroom Gusseted Poly Bags - Cleanroom Poly Sheets - Cleanroom Poly Pouches - Cleanroom Tote Covers - Cleanroom Pallet Covers - Cleanroom Square Bottom Bags Cleanroom HDPE - Cleanroom Packaging 

 DegageCorp. Anti-static low density polyethylene (MIL PRF-81705D) hand made clear, pink or black conductive shrouds and pallet sheets and Tote Covers (covers) are designed and custom made to the customer's requirements of a static control envelope to enclose electronic parts that are palletized and need protection from outside static surges. All pallet sheets, shrouds and covers are custom designed to the customers specifications and are manufactured in our "Hand Made" department. Average delivery time for pallet covers, shrouds and pallet sheets is 3 to 4 weeks. 

BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM. Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Governors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information : 

For other information, contact Degage Corp. (972) 524 - 2979 (Monday-Friday, 9:00am-5:00pm - central standard time)

Anti-Static Pallet Covers - Anti-Static LDPE - Anti-Static Pallet Sheets 

 DegageCorps. solid vinyl, static dissapative (10^8th ohms/sq.) floor surface mat is 1/8" thick and master roll sizes are 3'X105'. Available finnishes are wide rib, pebble finish or narrow v groove. Available colors are brown and grey, mats are cut to customer size specifications and installed with a standard grounding snap.

 DegageCorp low density polyethylene cleanroom packaging, "Perf on Roll" class 100 cleanroom bags on a roll, 2mil to 4mil are extruded from virgin resin, designed for "Easy Opening" and fabricated with a special perforation that will enable them to exceed the cleanliness specification of JPG-5322-1 Level 100, as well as ISO 14644-1 Class-5. Perforated on a roll bags are not normally used in a class 5 cleanroom however DegageCorp. has designed a special perforation machine combined with extra manufacturing tolerances enables us to produce an acceptable class 5 cleanroom certifiable product.

What Is JPG 5322.1G?    What Is JPG 14644?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Class 100 Bags on a roll - Class 100 Packaging - Class 100 LDPE 

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respritory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear Thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence  of acute toxicity, Skin Senitization, or sub-acute subchronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleating Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification ( Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazzardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information : 

For other information, contact Degage Corp. (972) 524 - 2979

  DegageCorps. Low density polyethylene, anti-static, non-corrosive bags (MIL B 22019C) are extruded from permanent anti-static resins with a non-corrosive additive that imparts a non-corrosive characteristic to the finished film, tubing or bags. DegageCorps. Non-corrosive bags are used to protect metal parts from the environment, humidity and potential for rust and contamination. DegageCorps. Non-corrosive bags are heavily used by the U.S Government for the shipping of hand held weapons and ammunition overseas and into unfriendly enviromental conditions. DegageCorps. Non-corrosive bags are normally tinted light blue but are available in any custom color to meet the customers specifications. 

BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:
Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use and/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Governors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979)Monday-Friday, 9:00am-5:00pm - central standard time

 DegageCorp. Low density polyethylene, class100, cleanroom tamper evident bags are manufactured in 2mil, 3mil, 4mil and 6mil, from virgin resin, without any manufacturing aides, release agents. Our special sealing system for tamper evident bags will protect your product from contamination, unauthorized inspection and any product degradation from an external environment, while exceeding the cleanliness specifications of JPG 5322-1 level100 as well as ISO 14644-1 class5. All bags are sub-packed 100 bags per sub-pack and each sub pack is certified with a certification label and double vacuum packed for secure contamination free, packaging in your cleanroom.

What Is JPG 5322.1G?    What Is JPG 14644?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM. 

Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.


EXPOSURE GUIDELINES:

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respritory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence  of acute toxicity, Skin Senitization, or sub-acute subchronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleating Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification ( Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazzardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information : 

For other information, contact Degage Corp. (972) 524 - 2979

 Our static shielding bags will meet the military specification of MIL-PRF-81705D, type 3. We currently offer this material in many configurations from a flat bag, gusseted bag and a Zip Lock bag. We also offer a CLEAN Static Shielding bag that will meet the cleanliness specification of NASA JPG 5322-1 Level 100 and ISO 14644-1 Class 5 (See DC-7000C). DegageCorps. metalized static shielding bags are a 3mil composite consisting of an outer layer of static dissipative coating applied to a layer of polyester that is vacuum deposited with a conductive aluminum metal coating and laminated to an inner layer of permanent static dissipative 10^8th low density polyethylene. The DegageCorp. transparent static shielding bag provides complete shielding from electrostatic discharge, RFI frequencies and EMI impulses. DegageCorps. Static shielding bags instantly dissipate static charges. Loaded circuit boards can be safely handled and stored, shipped and are readily identified without removal when placed in our transparent static shielding bags. Your products are static secure and totally enclosed in a Faraday Cage environment. Electrostatic voltages applied to the outside of the bag cannot affect components within the bag. This is not the case with Anti-Static bags which slowly dissipate static charges. Slow dissipation generally results in increased voltages inside anti-static polyethylene bags, potentially causing component degradation. The DegageCorp. Transparent static shielding is the best protection available for static sensitive components.

  DegageCorps. "Metal In"  static shielding bags meet  MIL-PRF-81705D, type III, class 1 Our metalized static shielding bags are a 3mil composite consisting of an outer layer of static dissipative coating applied to a layer of polyester that is vacuum deposited with a conductive aluminum metal coating and laminated to an inner layer of permanent, static dissipative 10^8th low density polyethylene. The DegageCorp transparent static shielding bag provides complete static shielding from electrostatic discharges, RFI frequencies and EMI impulses. Loaded circuit boards can be safely handled, stored, shipped and are readily identifiable without need for removal when placed in our transparent static shielding bags. Your products will be static secure and totally enclosed in a faraday cage environment when packaged in a DegageCorp. Transparent static shielding bag. Electrostatic voltages applied to the outside of the bag cannot affect components within the bag. This is not the case with anti-static bags which slowly dissipates static charges. Slow dissipation generally results in increased voltages inside anti-static polyethylene bags, potentially causing component degradation. 

  DegageCorps. low and high density, poly 35 gallon and 55 gallon, clean room class100, drum liners and trash bags are extruded from virgin resin without and manufacturing aides, release agents or slip agents, and will exceed the cleanliness requirements of JPG 5332-1 level 100 as well as ISO 14644 1 Plastic bag Class 5. DegageCorp. Drum liners and trash bags are designed for the biomedical field and are used to dispose of contaminated items in a clean room environment. DegageCorp. Cleanroom drum liners and trash bags are available in a cleanliness level as low as class 50 for those ultra-critical cleanliness environments. For custom sizes other than 35-55 gallon please call for quote and lead times on your cleanroom drum liners and trash can liners.  

What Is JPG 5322.1G?    What Is JPG 14644?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM. 

Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:
Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respiatory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

Class 100 LDPE - Class 100 HDPE - Cleanroom Drum Liners - Cleanroom Trash Bags - Cleanroom LDPE - Cleanroom HDPE - Cleanroom Packaging - ISO 14644 1 Plastic bag

 DegageCorps. low density, black carbon loaded and sealed, conductive 10^5th​ OHMS/SQ bags and film contains no release agents or slip agents, our black conductive bags are fabricated in line and are generally made in 3mil or 4mil and are used for the packaging of circuit boards or other static sensitive electronic items. DegageCorp. black conductive bags will also meet military specification MIL-P-82646A.

What Is JPG 5322.1G?    What Is JPG 14644?     What Is MIL-PRF-82646 A?    BPA Free Gaurantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

 DegageCorp. Low density, Cleanroom, Class100, ISO Class 5, black polyethylene, Carbon Loaded, Conductive, Silicon wafer liners and bags are extruded in a Class 5 cleanroom and die cut from sheeting into 6", 8", 10" and 12" circular wafer separators. Black conductive 10^5th Ohms/Sq. Bags are fabricated to cleanliness standard of JPG5322-1 Level 100 for the general cleanroom packaging of stacked wafers will meet Military Spec. Mil-P-82646A.

What Is JPG 5322.1G?    What Is MIL-PRF-82646 A?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:
Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

Respritory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON: Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute subchronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.

The information offered here is for the products shipped. Use and/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Governors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification ( Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

Cleanroom Wafer Bags - Class 100 Wafer Bags - Cleanroom Packaging - Class 100 Wafer Separators - Cleanroom LDPE - Class 100 LDPE 

 DegageCorp. Ultra low outgassing poly tubing, clean room bags class 100 - ISO Class 5 - are extruded in a Fed. Cert 209e cleanroom from specialty resins containing no manufacturing aides, release agents or slip agents, resulting in an ultra-pure environment for the packaging of precious metals and extremely contamination sensitive products. Because our films are both extruded and manufactured "In Line" inside of a Fed Cert 209e cleanroom the outside of our film and bags are as clean as they are inside. Ask us about the Ultra low outgassing poly tubing and bags. 

What Is JPG 5322.1G?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:
Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use and/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

Cleanroom Low Outgassing - Cleanroom Packaging - Class 100 Low Outgassing 

 DegageCorps. Low Density cleanroom polyethylene Clear zip lock bags, Class 100 (ISO Class 5), are manufactured as a side seal bag with the utilization of a clean room zipper that is custom designed to be air tight. Our zip lock bags will meet the stringent requirements of JPG 5322-1 Level 100 and are packaged 100 bags per double vacuum packed sub-pack and each pack is certified with a certification label. Zip lock bags are not normally used in a cleanroom environment due to the possibility of air leakage, however DegageCorp. uses a unique custom designed zipper that eliminates air leakage problems. 

What Is JPG 5322.1G?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM. 

Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:
Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use and/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Governors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

Cleanroom LDPE Zip Lock - Class 100 LDPE Zip Lock - Cleanroom LDPE Bags

 DegageCorps. Low density class 100 (ISO class 5) polyethylene cleanroom square bottom covers are handmade and hand cleaned in the "Hand Made" section of our Fed. 209E cleanroom. All bags are hand assembled and assembled and heat sealed on a custom designed Vertrod sealing machine from material that is extruded from Virgin resin without any slip agents, release agents or manufacturing aids. Class 100 square bottom covers are normally used for covering large electronic terminals and our covers will exceed the cleanliness standards of JPG 5322-1 Level 100

What Is JPG 5322.1G?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM. 

Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:
Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use and/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION: TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Governors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

Cleanroom LDPE - Cleanroom Totes - Cleanroom Square Bottom Bags - Class 100 Packaging 

  DegageCorps. Class 100 low density clean room poly shrouds, pallet sheeting and covers are manufactured in the environment of a Fed. Cert 209E cleanroom and are handmade and hand cleaned to meet the cleanliness specifications of JPG 5322-1 Level 100 and ISO 14644-1 Class 5. Cleanroom poly, pallet sheets and covers are normally combined with either pallet shrouds or handmade square bottom covers to give 100% coverage to large electronic switching terminals and transformers. 

What Is JPG 5322.1G?    What Is JPG 14644?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES:
Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION: TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

Cleanroom Sheeting - Class 100 Sheets - Cleanroom Pallet Covers 

 Narrow width gauge clean film is extruded to class 100 for use in the medical industry, in the packaging of catheters, surgical instruments, and small medical tubing. Widths down to 3/8" and thickness down to 2mil can be achieved without blocking or splitting and without the use of any release agents, slip agents or processing aides.

    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp . 002 - .008 LDPE        Composition/Information on Ingredients

Trace impurities and additional material names not listed above may also appear in the Regulatory Information section towards the end of the MSDS. These materials may be listed for local "Right to Know" compliance and for other reasons. 

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.

RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES: 

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

 Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.

 The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact DegageCorp. (972)524-2979 Monday-Friday, 9:00am-5:00pm central standard time

Cleanroom Tubing - Class 100 Tubing - Medical Tubing - LDPE Tubing 

  DegageCorps. Anti-Static pink or clear non corrosive low density Class 100 - ISO class 5 ESD bags are extruded using virgin resin without any release agents or slip agents and have a non-corrosive additive bonded to the resin molecules that enable our film to impart corrosion resistance to any metal parts packaged within its environment.  Our Anti-Static ESD non corrosive bags are blended with a permanent Anti-Stat that will not leach to the surface and will meet MIL Spec B 22019C as well as maintain a cleanliness level that exceeds the specification of JPG 5322-1 Level 100 and ISO 14644-1 Class 5.

What Is MIL-PRF-22019E?    What Is JPG 5322.1G?    What Is JPG 14644?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Available in the following configurations: Cleanroom Anti-Static Poly Bags - Cleanroom Anti-Static Zip Lock Poly Bags - Cleanroom Anti-Static Poly Tubing - Cleanroom Anti-Static Gusseted Poly Bags - Cleanroom Anti-Static Poly Sheets - Cleanroom Anti-Static Poly Pouches - Cleanroom Tote Covers - Cleanroom Pallet Covers - Cleanroom Anti-Static Square Bottom Bags - Cleanroom ESD Packaging

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp - CLEAR POLY BAGS, TUBING AND FILM.  Composition/Information on Ingredients

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.
RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES: 

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY: 

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence  of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.
The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact Degage Corp. (972) 524 - 2979

Cleanroom Non Corrosive - Class 100 Non Corrosive - Cleanroom LDPE - Cleanroom Packaging - Cleanroom Pink LDPE - Cleanroom ESD - Class 100 Pink LDPE ESD 

 DegageCorps. low density, polyethylene, cleanroom, class 100, ISO Class 5 vapor barrier bags is a mono structure film extruded in a FED. Cert 209E cleanroom that exhibits the characteristics of low vapor transmission while meeting the strict cleanliness specifications of JPG 5322-1 Level 100. Our mono film is extruded from a blend of low density resins that contain no release agents, slip agents, or manufacturing aides. See KleenTuff for additional specifications and test results. 

What Is JPG 5322.1G?    BPA Free Guarantee      BSE TSE Animal Component Free Guarantee      Latex Free Guarantee

 DegageCorps. low density, black carbon loaded and sealed, conductive 10^5th​ OHMS/SQ bags and film are extruded in a FED. Cert209E cleanroom from a special resin that contains no release agents or slip agents, our black conductive bags are fabricated in line and are generally made in 3mil or 4mil and are used for the packaging of circuit boards or other static sensitive electronic items. Our black conductive bags and film will meet and exceed the cleanliness requirements of JPG 5322-1 Level 100 as well as ISO 14644-1 Class 5 and are specially designed for admission into a class 5 cleanroom environment. DegageCorp. black conductive bags will also meet military specification MIL-P-82646A.

What Is JPG 5322.1G?    What Is JPG 14644?     What Is MIL-PRF-82646 A?    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee