DC-1290-CT Cleanroom Medical Poly Tubing Virgin Barefoot Narrow Width - JPG-5322-1 ISO Class 5 - 2Mil, 3Mil, 4Mil - 3/8

 Narrow width gauge clean film is extruded to class 100 for use in the medical industry, in the packaging of catheters, surgical instruments, and small medical tubing. Widths down to 3/8" and thickness down to 2mil can be achieved without blocking or splitting and without the use of any release agents, slip agents or processing aides.

    BPA Free Guarantee    BSE TSE Animal Component Free Guarantee    Latex Free Guarantee

Note: All values given are based on a 1.25mil thick film.

MATERIAL SAFETY DATA SHEET

DegageCorp . 002 - .008 LDPE        Composition/Information on Ingredients

Trace impurities and additional material names not listed above may also appear in the Regulatory Information section towards the end of the MSDS. These materials may be listed for local "Right to Know" compliance and for other reasons. 

HAZARDS IDENTIFICATION:

EMERGENCY OVERVIEW: A clear or colored plastic film. Not considered hazardous under normal usage. Can release irritating and/or toxic vapors if involved in a fire.

POTENTIAL HEALTH HAZARDS:

SKIN: Contact with molten material will cause thermal burns.
EYES: Vapors, Fumes or Sprays which can form at elevated temperature can be an irritant.
INHALATION: Not hazardous at ambient temperatures: Vapors, Fumes or sprays which can form at elevated temperatures are irritants to the eyes and respiratory tract. 
INGESTION: NOT a route of exposure. An adverse reaction is not expected.
DELAYED EFFECTS: None known
ENGINEERING CONTROLS: General room ventilation plus local exhaust at points of fume generation to maintain exposure below the PEL/TLV exposure limits.

PERSONAL PROTECTIVE EQUIPMENT:
SKIN PROTECTION: Not normally required. Use heat resistant gloves if handling melted material.
EYE PROTECTION: As a general practice in manufacturing areas, safety glasses that conform to ANSI Z87.1 should' be worn.

RESPIRATORY PROTECTION: Under normal usage, not normally required. A NIOSH/MSHA approved respirator should be worn in areas where the PEL/TLV is exceeded.

EXPOSURE GUIDELINES: 

Occupational Exposure: Nuisance dust TLV: 10mg/m³ (ACGIH)

Ventilation: Good general ventilation (typically 10 air changes per hour) Should be used. Ventilation rates should be matched to conditions.

Respiratory Protection: If engineering controls do not maintain airborne concentrations to an acceptable level, an approved respirator must be worn. In the United States of America, if respirators are used, a program should be instituted to assure compliance with OSHA standards 29 CFR 1910.134. Respirator type: Dust Organic Vapor.

Eye Protection: Wear Goggles or a face Shield when working with molten materials.

Skin Protection: Wear thermally resistant gloves and long sleeves when handling a molten product.

Recommended Decontamination Facilities:  Eye Bath, Washing Facilities 

PHYSICAL AND CHEMICAL PROPERTIES:

STABILITY AND REACTIVITY:

NORMALLY STABLE (CONDITIONS TO AVOID): Normally stable, Avoid exposure to open flame or temperatures exceeding recommended processing temperatures.
Incompatibilities: Strong oxidizing agents, acids, and bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition products may include: caprolactam, carbon monoxide, carbon dioxide, hydrogen Cyanide, and ammonia when exposed to extreme heat.
HAZARDOUS Polymerization: Will not occur.

TOXICOLOGICAL INFORMAITON:

Toxicity data is limited. There has been no evidence of acute toxicity, Skin Senitization, or sub-acute sub-chronic toxicity as a result of repeated exposure.

OTHER DISPOSAL CONSIDERATIONS:

 Dispose of in compliance with Federal, state and local government regulations. Usually considered an inert package material that can be recycled-or land filled.

 The information offered here is for the products shipped. Use an/or alterations to the product such as mixing with other materials may significantly change the characteristics of the material and alter the RCRA classification and proper disposal method.

TRANSPORT INFORMATION:
US DOT HAZZARD CLASS: Not regulated
US DOT ID#: Not applicable

REGULATORY INFORMATION:
TOXIC SUBSTANCES CONTROL ACT (TSCA)

TSCA INVENTORY STATUS: All components used to produce the above formulations-are listed on the TSCA Inventory.

OTHER TSCA issues: None

SARA TITLE III: In accordance with the provision of Title III, sections 311 & 312 of the Superfund amendmenments and authorization act, these products are not hazardous. These products do not contain Section 313 Reportable Ingredients.

California Prop 65: no reportable substances In Compliance 

CONEG: These products are in compliance with the heavy requirements of the Coalition of Northeastern Govenors

Ozone Depleting Substances: None reportable, in compliance with 40 CFR 82. 

Carcinogenicity Classification (Components present at 0.1% or more): None unless otherwise listed below:

IARC: (International Agency for Research on Cancer) None 

NTP: (National Toxicology Program) None 

European Hazardous Chemicals: None Reportable

DSL (Canadian Domestic Substances List): None Reportable

Other Information: 

For other information, contact DegageCorp. (972)524-2979 Monday-Friday, 9:00am-5:00pm central standard time

Cleanroom Tubing - Class 100 Tubing - Medical Tubing - LDPE Tubing